![]() Thepowerofbauer liked ZeroPhone - a Raspberry Pi smartphone.slightlylessstripeysnake has updated the log for Janktop IV Mini-ITX Laptop (Files Now Available).Mike Shaw liked OSI Challenger 4P Reproduction.Cal McKey liked Valor Tactical Stealth sUAS.CYUL has updated the log for HP Woodstock LiPo Battery Pack.Keshka wrote a comment on Solar Powered WiFi Weather Station V4.0.Graham Nicholson liked HP Woodstock LiPo Battery Pack.Natelolzzz wrote a comment on Edog - Mini 3D printed Quadruped Robot ✨.Michael Black on JFET Stands In For Triode In This Infinite Impedance Detector.Michael Black on Hackaday Podcast 205: Hackaday Berlin, So Many Sundials, And Ovens Pinging Google.Tyler Larson on ArtNet Not Going Through? Your Switch Might Be Protecting You.Daniel De Jager on XML Is A Quarter Century Old.paulvdh on A Look Back At The Xbox 360’s Hard Drive Security.Jan on RCA’s Clear Plastic TV Wowed Crowds In 1939.Michael Black on RCA’s Clear Plastic TV Wowed Crowds In 1939.Foldi-One on All About USB-C: Manufacturer Sins.Reluctant Cannibal on Deciphering Queen Of Scots, Mary Stuart’s Lost Letters.Kjw on Inputs Of Interest: The Infogrip BAT Chording Keyboard.It seems hard to lose at prices like these.Ĭontinue reading “Entry-Level 3D Printer Becomes Budget PCB Machine” → Posted in 3d Printer hacks, Tool Hacks Tagged Cetus, cnc, etching, g-code, laser, pcb, photoresistįox Fined For Using EAS Tone In Football Ad 80 Comments That was a $200 dedicated engraver, this is a $300 3D printer with a $30 laser. He recently tried the same thing using a cheap CNC laser engraver with similar results. This isn’t ’s first budget laser-etching rodeo. But the results are more than acceptable, especially for $330. The video below shows that the printer isn’t perfect for the job despite the smooth linear bearings, the low mass of the printer results in vibration that shows up as wavy traces. With a few mods to the cheap UV laser module had on hand, a printed holder for the laser, and a somewhat manual software toolchain, PCBs with 0.2-mm traces were soon being etched. But hiding beneath the covers was a suspicious transistor wired to a spare connector on the print head a little sleuthing and a call to the factory revealed that the pin is intended for accessory use and can be controlled from G-code. The printer has nice linear bearings but not a lot of other amenities, hence ’s desire to add a heated bed. ![]() The printer in question is a Cetus3D, one of the newer generation of affordable machines. And the results are pretty impressive, all the more so since so little effort and expense were involved. Instead of ending up with a heated bed, his $300 3D printer can now etch 0.2-mm PCB traces. From a trio of Cetus pro-tips to turning a Cetus into a PCB machine, the little printer has a lot to offer.Ĭontinue reading “This Cetus Printer Is Rigged For Silent Running” → Posted in 3d Printer hacks Tagged Cetus, decibels, extruder, fan, limit switches, stepper, TrinamicĪ funny thing happened on ’s way to upgrading his 3D printer. And Cetus hacking is becoming quite a thing around here. ![]() We’re tempted to try these silencing mods on our own Cetus, if ever publishes the BOM and PCB designs (hint, hint). As a bonus, the new PCB is much smaller than the original, leaving room to tuck the power supply into the case, which is a nice touch. It wasn’t cheap, and it meant basically gutting the printer, but the results are impressively quiet. The new board also supports the limit switches as well as thermostatic control of the extruder fan and pads for a platform heater. Inside the case, the electronics get a complete reworking, with a custom PCB to house Trinamic stepper drivers for ultraquiet operation. The first part of the video below reviews the shortcomings of the stock machine and the mechanical changes made, including new brackets for the Z-axis slide, relocating the WiFi antenna to someplace sensible, and adding limit switches for each slide. took this route and in the process made his Cetus 3D-printer essentially silent. But nothing is perfect, and to hit the $200 price point some compromises are inevitable. That doesn’t mean you have to live with those engineering choices, of course, which makes these cheap printers a great jumping off point for aftermarket mods. The entry-level 3D-printer market is a rich one, with offerings from many vendors that are surprisingly good.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |